Deluxe Strawberry Creme Hard Wax

Usage Instructions – Hard Wax

1. Area to be Waxed must be clean, dry and free from any oils and creams. Caronlab Australia recommends the use of Prep – Pre Wax Skin Cleanser as it has been designed to work together for best results with Caronlab Australia Waxes. Always test Wax on the inside of your wrist before use. Do not apply on warts, moles and broken or irritated skin.
2. You may begin by dipping Spatula into Wax, which should be the consistency of thick honey.
3. Apply Wax with the hair growth, leaving one edge thicker to create a lip. Hard Wax should be applied in a thick section. Wax will remain smooth and soft, maintaining its elasticity and pliability.
4. Hold skin taut and remove Wax by pulling in the opposite direction of hair growth.
5. For the perfect finish and to remove any Wax residue on the skin, we recommend you use After – After Waxing Oil and Soothe Mango & Witch Hazel or Tea Tree After Wax Soothing Lotion to complete your treatment. To clean equipment use Solvent – Wax Remover Citrus Clean.

Important

Store in a cool, dry place.

Warning

This is a professional product for Salon use only. Patch test before use. If skin irritation occurs, cease use. Exceeding the recommended instructions may cause burns and/or injury.

Heating Instructions – Microwave to Pot™ technology

1. Place Caronlab Australia Wax Heater Insert into your Caronlab Australia Professional Wax Heater. Microwave to Pot™ technology jars should be placed directly into a Wax Heater Insert.
2. To warm Wax directly in your Caronlab Australia Professional Wax Heater, remove the lid and insert jar directly into an appropriate professional Wax Heater on a medium setting.
3. To use Microwave to Pot™ technology, remove lid from jar and place off centre in microwave and heat for a minimum of 2 minutes, but no longer than 4 minutes depending on the wattage of your microwave and the amount of Wax remaining in the jar.
4. Once Wax has softened, place jar into your Caronlab Australia Wax Heater Insert. Regulate Heater to a medium setting of approximately 149°F–167°F or 65°C–75°C, between dial 3-4 on your Caronlab Australia Professional Wax Heater.
5. Dip Wax Spatula into Wax, at the correct consistency Wax should resemble a thick honey and should sit on the end of the Spatula and be practically dripless. If Wax is moving, it is too hot.

• Important: Do not heat over 140°C/284°F
• Place a Wax Heater Insert into your Caronlab Australia Professional Wax Heater. Microwave to Pot™ technology jars should not be placed directly into a Wax Heater
• Do not try this with other brands’ pots; they will melt in the Wax Heater

Heating Instructions – Tray Melts

1. Remove Wax from Tray by removing the plastic film, turn upside down and pop Melt out. In warmer climates we recommend you refrigerate or freeze Tray for 1-2 minutes before opening to help Melt pop out.
2. Place Melt into Caronlab Australia Professional Wax Heater, do not overfill past ¾ full.
3. Heat Wax on high for approximately 10 minutes, stirring regularly.
4. Regulate Heater to a medium setting or between dial 3-4 on a Caronlab Australia Professional Wax Heater or approximately 140°For 60°C.
5. Dip Wax Spatula into Wax, at the correct consistency Wax should resemble a thick honey and should sit on the end of the Spatula and be practically dripless. If Wax is moving, it is too hot. It is not necessary to melt down Wax completely, a core at the centre is ideal.
6. Top up Melts throughout use to maintain heat consistency, do not fill Insert past ¾ full and Wax should always be able to be stirred.

Heating Instructions – Beads

1. Place Wax Beads into the Caronlab Australia Professional Wax Heater Insert, no higher than ¾ full.
2. Heat on the highest setting for 20 minutes. DO NOT stir during this time.
3. When Wax is completely melted, turn down to 60°C (140°F) or between dial 3-4 on a Caronlab Australia Professional Wax Heater.
4. Dip Spatula into the Wax which should be the consistency of thick honey, if it’s dripping it is too hot.
5. DO NOT block the edges of the Professional Wax Heater Insert when topping up Beads. NO MORE than a scoop at a time.
6. Always work from a ¾ full Wax Heater.